Product ID:ENAMEL ALKYD GLOSS WHITE 17875
MSDS Date:12/29/1986
FSC:8010
NIIN:00-664-4761
MSDS Number: BHXCC

CON-LUX COATINGS, INC.

226 TALMADGE ROAD
EDISON, NJ 08818-0847
US

Emergency Phone: (206) 287-4000

Info Phone: (206) 287-4000

Cage: 60189

CON-LUX COATINGS INC

847 EDISON, NJ 08818-0847 US

Telephone: 732-287-4000

Cage: 60189

MINERAL SPIRITS

CAS: 64742-47-8

Fraction By Weight: 40.39%

OSHA PEL 100 PPM

TITANIUM DIOXIDE

CAS: 13463-67-7

RTECS: XR2275000

OSHA PEL 15 MG/M3 TDUST

ACGIH TLV: 10 MG/M3 TDUST; 9293

Routes of Entry: Inhalation:YES Skin:YES Ingestion:NO
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Effects of Overexposure:IRRITATION OF EYES AND SKIN MAY OCCUR WITH
OVEREXPOSURE. CONTINUED BREATHING OF VAPORS MAY IRRITATE
RESPIRATORY TRACT CAUSING HEADACHE, NAUSEA AND DIZZINESS.

First Aid:INHALATION: REMOVE TO FRESH AIR. RESTORE RESPIRATION IF
NECESSARY. TREAT SYMPTO-MATICALLY. EYE CONTACT: FLUSH IMMEDIATELY
WITH COPIOUS QUANTITIES OF WATER FOR 15 MIN. DERMAL CONTACT: WASH
AFFECTED AR EAS WITH SOAP AND WATER. REMOVE CONTAMI-NATED CLOTHING.
INGESTION: DRINK 1 OR 2 GLASSES OF WATER TO DILUTE.DO NOT
INDUCEVOMITING. IF SPONTANEOUS VOMITING OCCURS KEEP HEAD AT/BELOW
KNEE LEVEL.

Flash Point Method:TCC
Flash Point:105F 40.56C
Lower Limits:1.0
Extinguishing Media:FOAM, CO2, DRY CHEMICAL, WATER MIST
Fire Fighting Procedures:SMOTHER FLAMES WITH ONE OF THE ABOVE
EXTINGUISHING MEDIA. WATER MAY BE USED TO COOL DOWN UNOPENED
CONTAINERS IN VICINITY.
Unusual Fire/Explosion Hazard:CONTAINS FLAMMABLE SOLVENT. DO NOT USE IN
AREAS WHERE SPARKS OR OPEN FLAMES ARE PRESENT.

Spill Release Procedures:ELIMINATE ALL IGNITION SOURCES. WEAR
APPROPRIATE PERSONAL PROTECTION EQUIP. AND APPROVED
RESPIRATORCONTAIN SPILL WITH ABSORBENT MATERIAL & PUT INTO VAPOR
TIGHT CONTAINERS. PREVENT MATERIAL FROM CON- TACTING ANY WATER
SOURCES OR SEWERS.

Handling and Storage Precautions:STORE IN AREAS DESIGNED TO COMPLY WITH
ANSI/NFPA 30 FLAMMABL AN COMBUITBLE LIQUIDS CODE.
Other Precautions:GROUND CONTAINERS WHEN POURING LIQUIDS AND POWDERS TO
AVOID STATIC CHARG BUILD UP. DO NOT HANDLE UNTIL MANUFACTURERS
SAFETY PRECAUTIONS HAVE BEEN READ AND UNDERSTOOD.PROVIDE
ADEQUATE VENTILATION/ RESPIRATORY PROTECTION TO REMOVE DECOMP.

Respiratory Protection:IN OPEN AREAS, USE APPROVED RESPIRATOR TO REMOVE
SOLID AIRBORNE PARTICLES OF OVER SPRAY DURING SPRAY APPLICATION.
IN RESTRICTED VENTILATION AREAS USE APPROVERESPIRATOR DESIGN TO
REMOVE A COMBINATIO N OF PARTICLES AND VAPORS.
Ventilation:SUFFICIENT VENTILATION, IN VOLUME AND PATTERN, SHOULD BE
PROVIDED.
Protective Gloves:IMPERVIOUS TYPE
Eye Protection:SAFETY EYE WEAR
Other Protective Equipment:PREVENT PROLONGED SKIN CONTACT WITH
CONTAMINATED CLOTHING.
Work Hygienic Practices:WASH HANDS BEFORE EATING, SMOKING OR USING THE
WASHROOM FACILITIES.
Supplemental Safety and Health
NK

HCC:F4
Boiling Pt:B.P. Text:148 - 323F
Vapor Density:HEAVIER
Evaporation Rate & Reference:SLOWER THAN ETHER
Percent Volatiles by Volume:58.59

Stability Indicator/Materials to Avoid:YES
OXIDIZING AGENTS
Stability Condition to Avoid:EXTREME HEAT, SPARKS, OR OPEN FLAMES.
Hazardous Decomposition Products:MAY CAUSE HAZARDOUS FUMES WHEN HEATED.

Waste Disposal Methods:DISPOSE OF IN ACCORDANCE WITH FEDERAL, STATE AND
LOCAL REGULATIONS.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.